SSP6201
The SSP6201 series is a group of positive voltage output, three-pin regulators, that provide a high current even when the input/output voltage differential is small. Low power consumption and high accuracy is achieved through CMOS and laser trimming technologies.
The SSP6201 consists of a high-precision voltage reference, an error amplification circuit, and a current limited output driver. Transient response to load variations have improved in comparison to the existing series. SOT-89-3L packages is available.
SSP3085
The SSP3085 is a half-duplex high speed transceiver for RS-485 and RS422 communication. IC contains one driver and one receiver.
The SSP3085 has a fail-safe circuit, ensure logical high level of receiver output when receiver input is open or short. It can achieve error-free data transmission of up to 500kbps. Each driver output and receiver input is protected against ±15kV electrostatic discharge (HBM) (ESD)shocks.
The SSP3085 receiver has 1/8 unit load input impedance, allows up to 256 devices can be attached to the bus.
SSP1606
The SSP1606 is 16-bit, simultaneous sampling, analog-to-digital data acquisition systems (DAS) with eight channels, respectively. Each part contains analog input clamp protection, a second-order antialiasing filter, a track-and-hold amplifier, a 16-bit charge redistribution successive approximation analog-to-digital converter (ADC), a flexible digital filter, a 2.5V reference and reference buffer, and high speed
serial and parallel interfaces.
The SSP1606 operate from a single 5V supply and can accommodate±10V and ±5V true bipolar input signals while sampling at throughput rates up to 200kSPS for all channels. The input clamp protection circuitry can tolerate voltages up to ±16.5V. The SSP1606 has 1MΩ analog input impedance regardless of sampling frequency. The single supply operation, on-chip filtering, and high input impedance eliminate the need for driver op amps and external bipolar supplies. The SSP1606 antialiasing filter has a 3dB cutoff frequency of 22.9kHz and provides 40dB antialias rejection when sampling at 200kSPS. The flexible digital filter is pin driven, yields improvements in SNR.
SSP1220
The SSP1220 is a precision, 24-bit, analog-to-digital converter (ADC) that offers many integrated features to reduce system cost and component count in applications measuring small sensor signals. The device can perform conversions at data rates up to 2000 samples-per-second (SPS) with single-cycle settling. At 20 SPS, the digital filter offers simultaneous 50-Hz and 60-Hz rejection for noisy industrial applications. The internal PGA offers gains up to 128 V/V. This PGA makes the SSP1220 ideally suited for applications measuring small sensor signals, such as resistance temperature detectors (RTDs), thermocouples, thermistors, and bridge sensors.
Power consumption is as low as 120 µA@3.3V when operating in duty cycle mode with the PGA disabled.
The SSP1220 is offered in a TSSOP-16 package and is specified over a temperature range of –40℃ to +125℃.
SSP8099
The SSP8099 is a synchronous step-up converter . It is designed for products powered by alkaline battery, NiMH rechargeable battery, Li-Mn battery or rechargeable Li-Ion battery, for which high efficiency under light load condition is critical to achieve long battery life operation.
The SSP8099 can support up to 300mA output current from 3.3V to 5V conversion, and achieve up to 90% efficiency at 200mA load.
The SSP8099 also offers both down mode and pass-through operation for different applications. In down mode, the output voltage can still be regulated at target value even when input voltage is higher than output voltage. In pass-through mode, the output voltage follows input voltage. The SSP8099 exits down mode and enters into pass-through mode when VIN > VOUT + 0.3V.
The SSP8099 supports true shutdown function when it is disabled, which disconnects the load from the input supply to reduce the current consumption.
The SSP8099 offers both adjustable output voltage version and fixed output voltage versions. It is available in Green WLCSP-1.22×0.83-6B and TDFN-2×2-6AL packages.
SSP8011
The SSP8011 is a low-power single-key touch sensor IC. The operating mode is divided into Normal mode and Low Power mode. Button mode or Switching mode output can be choosed, and the output level mode is optional.
SSP7785
The SSP7785 is a high−performance linear regulator, offering a very wide operating input voltage range of up to 450 VDC, with an output current of up to 10 mA. Ideal for high input voltage applications.
The SSP7785 family offers ±5% initial accuracy, extremely high−power supply rejection ratio and ultra−low quiescent current. The SSP7785 is optimized for high−voltage line and load transients, making this part ideal for harsh environment applications. The SSP7785 is offered in fixed output voltage options
2.7V,3.3V and 5.0V.
SSP584X
SSP584X series is a Quad-channel digital isolator, using chip level high voltage isolation process, isolation voltage up to 5KVrms. This series of products have low radiation, excellent anti-electromagnetic interference performance, high transmission rate and low power consumption; Equipped with enable pins to place the output in a high impedance state.
It has fail-safe mode, which can restore the output to the default state when the input power loss. This series of products have 4 in 0 out, 3 in 1 out, 2 in 2 out and other specifications, the specific product information, see the product selection table.
SSP721A
SSP721A is a single chip transceiver developed for Meter-Bus standard (EN1434-3、EN13757) applications.
The SSP721A interface circuit adjusts the different potentials between a slave system and the Meter-Bus master. The connection to the bus is polarity independent and supports full galvanic slave isolation with optocouplers. The circuit is supplied by the master via the bus. Therefore, this circuit offers no additional load for the slave battery. A power-fail function is integrated. The receiver has dynamic level recognition, and the transmitter has a programmable current sink. A 3.3V voltage regulator, with power reserve for a delayed switch off at bus fault, is integrated.
SSP97950
SSP97950 is a general LCD driver IC with 8COMx35SEG total output capacity of 280 bits, suitable for commonly used character/graphic LCD screens. SSP97950 support serial data interface(I2C).
